Sandblasting Tools and Supplies - Sundance Art Glass Center
Sundance Art Glass
All Torches Glassblowing Pyrex Pipemaking Lampworking Beadmaking Soft Glass & Hard Glass Nortel Carlisle National GTT Gas Equipment Oxygen Concentrators Torch Tips
Moretti/Effetre Soft Glass Borosilicate Hard Glass/Pyrex Bullseye Glass Dichroic Rods/Tubing Fusing Glass COE 33 COE 90 COE104
Moretti/Effetre Soft Glass Borosilicate/Pyrex Hard Glass Bullseye Dichroic Glassblowing Sculpture Boro
Fusing Tool Kits Gas Equipment Kits
Glassblowing Pyrex Pipemaking Lampworking Beadmaking Soft Glass Hard Glass Fusing Our Newsletter!
Lampworking Glassblowing Fusing Glass Bead casting
Lampworking Borosilicate Pyrex Glass Bead Soft Glass
Fusing Lampworking Beadmaking Glassblowing
For Fusing For Stained Glass
COE 90 Effetre COE 104 Borosilicate COE 33
Fusing Bead Lampworking Glassblowing Crucible Kiln Kiln Controllers Kiln Pyrometers Kiln Shelves and Posts
Lampworking Soft Glass Beadmaking GlassBlowing Hard Glass Pyrex Pipemaking

Sandblasted Glass

Temporarily Out of Stock

Compressor Requirements 2 HP or larger
Minimum Air Consumption 3.3 CFM
Minimum Air Pressure 90 PSI
Hopper Capacity 2-1/2 gallon/30 lbs.


WARNING: When using pneumatic equipment, basic safety precautions should always be followed to reduce the risk of personal injury and hazards due to over pressurization. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.

2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations. Don't expose to rain. Keep work area well lit. Do not use electrically powered air compressors in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them handle machines, tools, or hoses.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool's capacities.

6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not intended.

7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in moving parts. Non-skid footwear is recommended. Wear restrictive hair covering to contain long hair.

8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash goggles. Always wear ANSI approved impact safety goggles at other times. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists.

9. DO NOT ABUSE THE POWER CORD. Do not yank compressor's cord to disconnect it from receptacle. Do not carry tools by the cord.

10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines.

11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect compressor's cord periodically and, if damaged, have them repaired by an authorized technician. Inspect all hoses for leaks prior to use. The handles must be kept clean, dry, and free from oil and grease at all times.

12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in.

13. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your finger on the trigger, whether it is connected to the compressor or not.

14. STAY ALERT. Watch what you are doing; use common sense. Do not operate any tool when you are tired.

15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment an d binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn on and off properly.

16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools.

17. DO NOT OPERATE TOOL IF UNDER INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes will be impaired while taking these drugs. If there is any doubt, do not operate the tool.

18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the compressor. Do not allow compressor to sit pressurized for longer than an hour.

19. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you are using.



Register Account | Login
View Account | Logout
Shopping Cart
Secure Shopping
Secure Checkout
New Stuff And Sales!
Clearance Items!

Home | About Us | Store Locator | Wholesale Qualifications
Order | Employment Opportunities
Contact Us | Sitemap

Copyright & ™ 2008 Sundance Art Glass. All rights reserved.
Sundance Art Glass, 6052 Foster Rd., Paradise, CA, 95969-3121, USA
Phone: 800-641-6262  |